This patch removes unused macros defined in MvPhyDxe.h, as well
as improves the style and comments. Pick single definition
of the autonegotiation timeout - two different macros were used
for the same purpose.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
---
Platform/Marvell/Drivers/Net/Phy/MvPhyDxe/MvPhyDxe.c | 2 +-
Platform/Marvell/Drivers/Net/Phy/MvPhyDxe/MvPhyDxe.h | 152 ++++----------------
2 files changed, 31 insertions(+), 123 deletions(-)
diff --git a/Platform/Marvell/Drivers/Net/Phy/MvPhyDxe/MvPhyDxe.c b/Platform/Marvell/Drivers/Net/Phy/MvPhyDxe/MvPhyDxe.c
index e776a91..dd2edae 100644
--- a/Platform/Marvell/Drivers/Net/Phy/MvPhyDxe/MvPhyDxe.c
+++ b/Platform/Marvell/Drivers/Net/Phy/MvPhyDxe/MvPhyDxe.c
@@ -328,7 +328,7 @@ MvPhyInit1512 (
DEBUG((DEBUG_ERROR, "MvPhyDxe: Waiting for PHY auto negotiation... "));
for (i = 0; !(Data & BMSR_ANEGCOMPLETE); i++) {
- if (i > PHY_ANEG_TIMEOUT) {
+ if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
DEBUG((DEBUG_ERROR, "timeout\n"));
PhyDev->LinkUp = FALSE;
return EFI_TIMEOUT;
diff --git a/Platform/Marvell/Drivers/Net/Phy/MvPhyDxe/MvPhyDxe.h b/Platform/Marvell/Drivers/Net/Phy/MvPhyDxe/MvPhyDxe.h
index 0c3d935..66974bb 100644
--- a/Platform/Marvell/Drivers/Net/Phy/MvPhyDxe/MvPhyDxe.h
+++ b/Platform/Marvell/Drivers/Net/Phy/MvPhyDxe/MvPhyDxe.h
@@ -34,137 +34,45 @@ SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
#ifndef __MV_PHY_DXE_H__
#define __MV_PHY_DXE_H__
-#define MII_BMCR 0x00 /* Basic mode control Register */
-#define MII_BMSR 0x01 /* Basic mode status Register */
-#define MII_PHYSID1 0x02 /* PHYS ID 1 */
-#define MII_PHYSID2 0x03 /* PHYS ID 2 */
-#define MII_ADVERTISE 0x04 /* Advertisement control Reg */
-#define MII_LPA 0x05 /* Link partner ability Reg */
-#define MII_EXPANSION 0x06 /* Expansion Register */
-#define MII_CTRL1000 0x09 /* 1000BASE-T control */
-#define MII_STAT1000 0x0a /* 1000BASE-T status */
-#define MII_ESTATUS 0x0f /* Extended Status */
-#define MII_DCOUNTER 0x12 /* Disconnect counter */
-#define MII_FCSCOUNTER 0x13 /* False carrier counter */
-#define MII_NWAYTEST 0x14 /* N-way auto-neg test Reg */
-#define MII_RERRCOUNTER 0x15 /* Receive error counter */
-#define MII_SREVISION 0x16 /* Silicon revision */
-#define MII_RESV1 0x17 /* Reserved... */
-#define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */
-#define MII_PHYADDR 0x19 /* PHY address */
-#define MII_RESV2 0x1a /* Reserved... */
-#define MII_TPISTATUS 0x1b /* TPI status for 10mbps */
-#define MII_NCONFIG 0x1c /* Network interface config */
-
-/* Basic mode control Register. */
-#define BMCR_RESV 0x003f /* Unused... */
-#define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */
-#define BMCR_CTST 0x0080 /* Collision test */
-#define BMCR_FULLDPLX 0x0100 /* Full duplex */
-#define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */
-#define BMCR_ISOLATE 0x0400 /* Disconnect DP83840 from MII */
-#define BMCR_PDOWN 0x0800 /* Powerdown the DP83840 */
-#define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */
-#define BMCR_SPEED100 0x2000 /* Select 100Mbps */
-#define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */
-#define BMCR_RESET 0x8000 /* Reset the DP83840 */
-
-/* Basic mode status Register. */
-#define BMSR_ERCAP 0x0001 /* Ext-Reg capability */
-#define BMSR_JCD 0x0002 /* Jabber detected */
-#define BMSR_LSTATUS 0x0004 /* Link status */
-#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */
-#define BMSR_RFAULT 0x0010 /* Remote fault detected */
-#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */
-#define BMSR_RESV 0x00c0 /* Unused... */
-#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */
-#define BMSR_100HALF2 0x0200 /* Can do 100BASE-T2 HDX */
-#define BMSR_100FULL2 0x0400 /* Can do 100BASE-T2 FDX */
-#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */
-#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */
-#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */
-#define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */
-#define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */
-
-#define PHY_ANEG_TIMEOUT 4000
-
-#define PHY_INTERFACE_MODE_RGMII 0
-#define PHY_INTERFACE_MODE_RGMII_ID 1
-#define PHY_INTERFACE_MODE_RGMII_RXID 2
-#define PHY_INTERFACE_MODE_RGMII_TXID 3
-#define PHY_INTERFACE_MODE_SGMII 4
-#define PHY_INTERFACE_MODE_RTBI 5
-
-#define PHY_AUTONEGOTIATE_TIMEOUT 5000
+#define MII_BMCR 0x00 /* Basic mode control Register */
+#define MII_BMSR 0x01 /* Basic mode status Register */
+
+/* BMCR */
+#define BMCR_ANRESTART 0x0200 /* 1 = Restart autonegotiation */
+#define BMCR_ISOLATE 0x0400 /* 0 = Isolate PHY */
+#define BMCR_ANENABLE 0x1000 /* 1 = Enable autonegotiation */
+#define BMCR_RESET 0x8000 /* 1 = Reset the PHY */
+
+/* BSMR */
+#define BMSR_LSTATUS 0x0004 /* 1 = Link up */
+#define BMSR_ANEGCAPABLE 0x0008 /* 1 = Able to perform auto-neg */
+#define BMSR_ANEGCOMPLETE 0x0020 /* 1 = Auto-neg complete */
+
+#define PHY_AUTONEGOTIATE_TIMEOUT 5000
/* 88E1011 PHY Status Register */
-#define MIIM_88E1xxx_PHY_STATUS 0x11
-#define MIIM_88E1xxx_PHYSTAT_SPEED 0xc000
-#define MIIM_88E1xxx_PHYSTAT_GBIT 0x8000
-#define MIIM_88E1xxx_PHYSTAT_100 0x4000
-#define MIIM_88E1xxx_PHYSTAT_DUPLEX 0x2000
-#define MIIM_88E1xxx_PHYSTAT_SPDDONE 0x0800
-#define MIIM_88E1xxx_PHYSTAT_LINK 0x0400
-
-#define MIIM_88E1xxx_PHY_SCR 0x10
-#define MIIM_88E1xxx_PHY_MDI_X_AUTO 0x0060
-
-/* 88E1111 PHY LED Control Register */
-#define MIIM_88E1111_PHY_LED_CONTROL 24
-#define MIIM_88E1111_PHY_LED_DIRECT 0x4100
-#define MIIM_88E1111_PHY_LED_COMBINE 0x411C
+#define MIIM_88E1xxx_PHY_STATUS 0x11
+#define MIIM_88E1xxx_PHYSTAT_SPEED 0xc000
+#define MIIM_88E1xxx_PHYSTAT_GBIT 0x8000
+#define MIIM_88E1xxx_PHYSTAT_100 0x4000
+#define MIIM_88E1xxx_PHYSTAT_DUPLEX 0x2000
+#define MIIM_88E1xxx_PHYSTAT_SPDDONE 0x0800
+#define MIIM_88E1xxx_PHYSTAT_LINK 0x0400
/* 88E1111 Extended PHY Specific Control Register */
-#define MIIM_88E1111_PHY_EXT_CR 0x14
-#define MIIM_88E1111_RX_DELAY 0x80
-#define MIIM_88E1111_TX_DELAY 0x2
+#define MIIM_88E1111_PHY_EXT_CR 0x14
+#define MIIM_88E1111_RX_DELAY 0x80
+#define MIIM_88E1111_TX_DELAY 0x02
/* 88E1111 Extended PHY Specific Status Register */
-#define MIIM_88E1111_PHY_EXT_SR 0x1b
-#define MIIM_88E1111_HWCFG_MODE_MASK 0xf
+#define MIIM_88E1111_PHY_EXT_SR 0x1b
+#define MIIM_88E1111_HWCFG_MODE_MASK 0xf
#define MIIM_88E1111_HWCFG_MODE_COPPER_RGMII 0xb
-#define MIIM_88E1111_HWCFG_MODE_FIBER_RGMII 0x3
+#define MIIM_88E1111_HWCFG_MODE_FIBER_RGMII 0x3
#define MIIM_88E1111_HWCFG_MODE_SGMII_NO_CLK 0x4
-#define MIIM_88E1111_HWCFG_MODE_COPPER_RTBI 0x9
+#define MIIM_88E1111_HWCFG_MODE_COPPER_RTBI 0x9
#define MIIM_88E1111_HWCFG_FIBER_COPPER_AUTO 0x8000
-#define MIIM_88E1111_HWCFG_FIBER_COPPER_RES 0x2000
-
-#define MIIM_88E1111_COPPER 0
-#define MIIM_88E1111_FIBER 1
-
-/* 88E1118 PHY defines */
-#define MIIM_88E1118_PHY_PAGE 22
-#define MIIM_88E1118_PHY_LED_PAGE 3
-
-/* 88E1121 PHY LED Control Register */
-#define MIIM_88E1121_PHY_LED_CTRL 16
-#define MIIM_88E1121_PHY_LED_PAGE 3
-#define MIIM_88E1121_PHY_LED_DEF 0x0030
-
-/* 88E1121 PHY IRQ Enable/Status Register */
-#define MIIM_88E1121_PHY_IRQ_EN 18
-#define MIIM_88E1121_PHY_IRQ_STATUS 19
-
-#define MIIM_88E1121_PHY_PAGE 22
-
-/* 88E1145 Extended PHY Specific Control Register */
-#define MIIM_88E1145_PHY_EXT_CR 20
-#define MIIM_M88E1145_RGMII_RX_DELAY 0x0080
-#define MIIM_M88E1145_RGMII_TX_DELAY 0x0002
-
-#define MIIM_88E1145_PHY_LED_CONTROL 24
-#define MIIM_88E1145_PHY_LED_DIRECT 0x4100
-
-#define MIIM_88E1145_PHY_PAGE 29
-#define MIIM_88E1145_PHY_CAL_OV 30
-
-#define MIIM_88E1149_PHY_PAGE 29
-
-/* 88E1310 PHY defines */
-#define MIIM_88E1310_PHY_LED_CTRL 16
-#define MIIM_88E1310_PHY_IRQ_EN 18
-#define MIIM_88E1310_PHY_RGMII_CTRL 21
-#define MIIM_88E1310_PHY_PAGE 22
+#define MIIM_88E1111_HWCFG_FIBER_COPPER_RES 0x2000
typedef enum {
MV_PHY_DEVICE_1512
--
2.7.4
_______________________________________________
edk2-devel mailing list
edk2-devel@lists.01.org
https://lists.01.org/mailman/listinfo/edk2-devel
© 2016 - 2024 Red Hat, Inc.