[edk2] [PATCH v2 10/13] ArmPlatformPkg: remove PL34xDmc driver

Ard Biesheuvel posted 13 patches 7 years ago
[edk2] [PATCH v2 10/13] ArmPlatformPkg: remove PL34xDmc driver
Posted by Ard Biesheuvel 7 years ago
Remove PL34xDmc driver which is not used by any platforms

Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by-if-no-comments-by-15-Dec: Leif Lindholm <leif.lindholm@linaro.org>
---
 ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.c   | 227 -------------
 ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.inf |  29 --
 ArmPlatformPkg/Include/Drivers/PL341Dmc.h    | 336 --------------------
 3 files changed, 592 deletions(-)

diff --git a/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.c b/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.c
deleted file mode 100644
index 08eba6ec6930..000000000000
--- a/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.c
+++ /dev/null
@@ -1,227 +0,0 @@
-/** @file
-*
-*  Copyright (c) 2011, ARM Limited. All rights reserved.
-*
-*  This program and the accompanying materials
-*  are licensed and made available under the terms and conditions of the BSD License
-*  which accompanies this distribution.  The full text of the license may be found at
-*  http://opensource.org/licenses/bsd-license.php
-*
-*  THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
-*  WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
-*
-**/
-
-#include <Uefi.h>
-
-#include <Library/IoLib.h>
-#include <Library/DebugLib.h>
-
-#include <Drivers/PL341Dmc.h>
-
-// Macros for writing to DDR2 controller.
-#define DmcWriteReg(reg,val)                    MmioWrite32(DmcBase + reg, val)
-#define DmcReadReg(reg)                         MmioRead32(DmcBase + reg)
-
-// Macros for writing/reading to DDR2 PHY controller
-#define DmcPhyWriteReg(reg,val)                    MmioWrite32(DmcPhyBase + reg, val)
-#define DmcPhyReadReg(reg)                         MmioRead32(DmcPhyBase + reg)
-
-// Initialise PL341 Dynamic Memory Controller
-VOID
-PL341DmcInit (
-  IN  UINTN             DmcBase,
-  IN  PL341_DMC_CONFIG* DmcConfig
-  )
-{
-  UINTN Index;
-  UINT32 Chip;
-
-  // Set config mode
-  DmcWriteReg(DMC_COMMAND_REG, DMC_COMMAND_CONFIGURE);
-
-  //
-  // Setup the QoS AXI ID bits
-  //
-  if (DmcConfig->HasQos) {
-    // CLCD AXIID = 000
-    DmcWriteReg(DMC_ID_0_CFG_REG, DMC_ID_CFG_QOS_ENABLE | DMC_ID_CFG_QOS_MIN);
-
-    // Default disable QoS
-    DmcWriteReg(DMC_ID_1_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_2_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_3_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_4_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_5_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_6_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_7_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_8_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_9_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_10_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_11_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_12_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_13_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_14_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-    DmcWriteReg(DMC_ID_15_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
-  }
-
-  //
-  // Initialise memory controlller
-  //
-  DmcWriteReg(DMC_REFRESH_PRD_REG, DmcConfig->RefreshPeriod);
-  DmcWriteReg(DMC_CAS_LATENCY_REG, DmcConfig->CasLatency);
-  DmcWriteReg(DMC_WRITE_LATENCY_REG, DmcConfig->WriteLatency);
-  DmcWriteReg(DMC_T_MRD_REG, DmcConfig->t_mrd);
-  DmcWriteReg(DMC_T_RAS_REG, DmcConfig->t_ras);
-  DmcWriteReg(DMC_T_RC_REG, DmcConfig->t_rc);
-  DmcWriteReg(DMC_T_RCD_REG, DmcConfig->t_rcd);
-  DmcWriteReg(DMC_T_RFC_REG, DmcConfig->t_rfc);
-  DmcWriteReg(DMC_T_RP_REG, DmcConfig->t_rp);
-  DmcWriteReg(DMC_T_RRD_REG, DmcConfig->t_rrd);
-  DmcWriteReg(DMC_T_WR_REG, DmcConfig->t_wr);
-  DmcWriteReg(DMC_T_WTR_REG, DmcConfig->t_wtr);
-  DmcWriteReg(DMC_T_XP_REG, DmcConfig->t_xp);
-  DmcWriteReg(DMC_T_XSR_REG, DmcConfig->t_xsr);
-  DmcWriteReg(DMC_T_ESR_REG, DmcConfig->t_esr);
-  DmcWriteReg(DMC_T_FAW_REG, DmcConfig->t_faw);
-  DmcWriteReg(DMC_T_WRLAT_DIFF, DmcConfig->t_wdata_en);
-  DmcWriteReg(DMC_T_RDATA_EN, DmcConfig->t_data_en);
-
-  //
-  // Initialise PL341 Mem Config Registers
-  //
-
-  // Set PL341 Memory Config
-  DmcWriteReg(DMC_MEMORY_CONFIG_REG, DmcConfig->MemoryCfg);
-
-  // Set PL341 Memory Config 2
-  DmcWriteReg(DMC_MEMORY_CFG2_REG, DmcConfig->MemoryCfg2);
-
-  // Set PL341 Memory Config 3
-  DmcWriteReg(DMC_MEMORY_CFG3_REG, DmcConfig->MemoryCfg3);
-
-  // Set PL341 Chip Select <n>
-  DmcWriteReg(DMC_CHIP_0_CFG_REG, DmcConfig->ChipCfg0);
-  DmcWriteReg(DMC_CHIP_1_CFG_REG, DmcConfig->ChipCfg1);
-  DmcWriteReg(DMC_CHIP_2_CFG_REG, DmcConfig->ChipCfg2);
-  DmcWriteReg(DMC_CHIP_3_CFG_REG, DmcConfig->ChipCfg3);
-
-  // Delay
-  for (Index = 0; Index < 10; Index++) {
-    DmcReadReg(DMC_STATUS_REG);
-  }
-
-  if (DmcConfig->IsUserCfg) {
-    //
-    // Set Test Chip PHY Registers via PL341 User Config Reg
-    // Note that user_cfgX registers are Write Only
-    //
-    // DLL Freq set = 250MHz - 266MHz
-    //
-    DmcWriteReg(DMC_USER_0_CFG_REG, DmcConfig->User0Cfg);
-
-    // user_config2
-    // ------------
-    // Set defaults before calibrating the DDR2 buffer impendence
-    // - Disable ODT
-    // - Default drive strengths
-    DmcWriteReg(DMC_USER_2_CFG_REG, 0x40000198);
-
-    //
-    // Auto calibrate the DDR2 buffers impendence
-    //
-    while (!(DmcReadReg(DMC_USER_STATUS_REG) & 0x100));
-
-    // Set the output driven strength
-    DmcWriteReg(DMC_USER_2_CFG_REG, 0x40800000 | DmcConfig->User2Cfg);
-
-    //
-    // Set PL341 Feature Control Register
-    //
-    // Disable early BRESP - use to optimise CLCD performance
-    DmcWriteReg(DMC_FEATURE_CRTL_REG, 0x00000001);
-  }
-
-  //
-  // Config memories
-  //
-  for (Chip = 0; Chip < DmcConfig->MaxChip; Chip++) {
-    // Send nop
-    DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_NOP);
-
-    // Pre-charge all
-    DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_PRECHARGEALL);
-
-    // Delay
-    for (Index = 0; Index < 10; Index++) {
-      DmcReadReg(DMC_STATUS_REG);
-    }
-
-    // Set (EMR2) extended mode register 2
-    DmcWriteReg(DMC_DIRECT_CMD_REG,
-      DMC_DIRECT_CMD_CHIP_ADDR(Chip) |
-      DMC_DIRECT_CMD_BANKADDR(2) |
-      DMC_DIRECT_CMD_MEMCMD_EXTMODEREG);
-
-    // Set (EMR3) extended mode register 3
-    DmcWriteReg(DMC_DIRECT_CMD_REG,
-      DMC_DIRECT_CMD_CHIP_ADDR(Chip) |
-      DMC_DIRECT_CMD_BANKADDR(3) |
-      DMC_DIRECT_CMD_MEMCMD_EXTMODEREG);
-
-    //
-    // Set (EMR) Extended Mode Register
-    //
-    // Put into OCD default state
-    DmcWriteReg(DMC_DIRECT_CMD_REG,DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_BANKADDR(1) | DMC_DIRECT_CMD_MEMCMD_EXTMODEREG);
-
-    //
-    // Set (MR) mode register - With DLL reset
-    //
-    DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_EXTMODEREG | DmcConfig->ModeReg | DDR2_MR_DLL_RESET);
-
-    // Pre-charge all
-    DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_PRECHARGEALL);
-    // Auto-refresh
-    DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_AUTOREFRESH);
-    // Auto-refresh
-    DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_AUTOREFRESH);
-
-    //
-    // Set (MR) mode register - Without DLL reset
-    //
-    DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_EXTMODEREG | DmcConfig->ModeReg);
-
-    // Delay
-    for (Index = 0; Index < 10; Index++) {
-      DmcReadReg(DMC_STATUS_REG);
-    }
-
-    //
-    // Set (EMR) extended mode register - Enable OCD defaults
-    //
-    DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | (0x00090000) |
-        (1 << DDR_MODESET_SHFT) | (DDR_EMR_OCD_DEFAULT << DDR_EMR_OCD_SHIFT) | DmcConfig->ExtModeReg);
-
-    // Delay
-    for (Index = 0; Index < 10; Index++) {
-      DmcReadReg(DMC_STATUS_REG);
-    }
-
-    // Set (EMR) extended mode register - OCD Exit
-    DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | (0x00090000) |
-        (1 << DDR_MODESET_SHFT) | (DDR_EMR_OCD_NS << DDR_EMR_OCD_SHIFT) | DmcConfig->ExtModeReg);
-
-    // Delay
-    for (Index = 0; Index < 10; Index++) {
-      DmcReadReg(DMC_STATUS_REG);
-    }
-  }
-
-  // Move DDR2 Controller to Ready state by issueing GO command
-  DmcWriteReg(DMC_COMMAND_REG, DMC_COMMAND_GO);
-
-  // wait for ready
-  while (!(DmcReadReg(DMC_STATUS_REG) & DMC_STATUS_READY));
-
-}
diff --git a/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.inf b/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.inf
deleted file mode 100644
index 0f3d862e14ef..000000000000
--- a/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.inf
+++ /dev/null
@@ -1,29 +0,0 @@
-#/* @file
-#  Copyright (c) 2011, ARM Limited. All rights reserved.
-#
-#  This program and the accompanying materials
-#  are licensed and made available under the terms and conditions of the BSD License
-#  which accompanies this distribution.  The full text of the license may be found at
-#  http://opensource.org/licenses/bsd-license.php
-#
-#  THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
-#  WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
-#
-#*/
-
-[Defines]
-  INF_VERSION                    = 0x00010005
-  BASE_NAME                      = PL341Dmc
-  FILE_GUID                      = edf8da40-aad1-11df-a1f4-0002a5d5c51b
-  MODULE_TYPE                    = BASE
-  VERSION_STRING                 = 1.0
-  LIBRARY_CLASS                  = PL341DmcLib
-
-[Sources]
-  PL341Dmc.c
-
-[Packages]
-  ArmPlatformPkg/ArmPlatformPkg.dec
-  MdePkg/MdePkg.dec
-
-[FixedPcd]
diff --git a/ArmPlatformPkg/Include/Drivers/PL341Dmc.h b/ArmPlatformPkg/Include/Drivers/PL341Dmc.h
deleted file mode 100644
index caba8f445bd8..000000000000
--- a/ArmPlatformPkg/Include/Drivers/PL341Dmc.h
+++ /dev/null
@@ -1,336 +0,0 @@
-/** @file
-*
-*  Copyright (c) 2011, ARM Limited. All rights reserved.
-*
-*  This program and the accompanying materials
-*  are licensed and made available under the terms and conditions of the BSD License
-*  which accompanies this distribution.  The full text of the license may be found at
-*  http://opensource.org/licenses/bsd-license.php
-*
-*  THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
-*  WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
-*
-**/
-
-#ifndef _PL341DMC_H_
-#define _PL341DMC_H_
-
-
-typedef struct  {
-    UINTN   HasQos;        // has QoS registers
-    UINTN   MaxChip;       // number of memory chips accessible
-    BOOLEAN IsUserCfg;
-    UINT32  User0Cfg;
-    UINT32  User2Cfg;
-    UINT32  RefreshPeriod;
-    UINT32  CasLatency;
-    UINT32  WriteLatency;
-    UINT32  t_mrd;
-    UINT32  t_ras;
-    UINT32  t_rc;
-    UINT32  t_rcd;
-    UINT32  t_rfc;
-    UINT32  t_rp;
-    UINT32  t_rrd;
-    UINT32  t_wr;
-    UINT32  t_wtr;
-    UINT32  t_xp;
-    UINT32  t_xsr;
-    UINT32  t_esr;
-    UINT32  MemoryCfg;
-    UINT32  MemoryCfg2;
-    UINT32  MemoryCfg3;
-    UINT32  ChipCfg0;
-    UINT32  ChipCfg1;
-    UINT32  ChipCfg2;
-    UINT32  ChipCfg3;
-    UINT32  t_faw;
-    UINT32  t_data_en;
-    UINT32  t_wdata_en;
-    UINT32  ModeReg;
-    UINT32  ExtModeReg;
-} PL341_DMC_CONFIG;
-
-/* Memory config bit fields */
-#define DMC_MEMORY_CONFIG_COLUMN_ADDRESS_9      0x1
-#define DMC_MEMORY_CONFIG_COLUMN_ADDRESS_10     0x2
-#define DMC_MEMORY_CONFIG_COLUMN_ADDRESS_11     0x3
-#define DMC_MEMORY_CONFIG_COLUMN_ADDRESS_12     0x4
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_11        (0x0 << 3)
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_12        (0x1 << 3)
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_13        (0x2 << 3)
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_14        (0x3 << 3)
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_15        (0x4 << 3)
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_16        (0x5 << 3)
-#define DMC_MEMORY_CONFIG_BURST_2               (0x1 << 15)
-#define DMC_MEMORY_CONFIG_BURST_4               (0x2 << 15)
-#define DMC_MEMORY_CONFIG_BURST_8               (0x3 << 15)
-#define DMC_MEMORY_CONFIG_BURST_16              (0x4 << 15)
-#define DMC_MEMORY_CONFIG_ACTIVE_CHIP_1    (0x0 << 21)
-#define DMC_MEMORY_CONFIG_ACTIVE_CHIP_2    (0x1 << 21)
-#define DMC_MEMORY_CONFIG_ACTIVE_CHIP_3    (0x2 << 21)
-#define DMC_MEMORY_CONFIG_ACTIVE_CHIP_4    (0x3 << 21)
-
-#define DMC_MEMORY_CFG2_CLK_ASYNC    (0x0 << 0)
-#define DMC_MEMORY_CFG2_CLK_SYNC    (0x1 << 0)
-#define DMC_MEMORY_CFG2_DQM_INIT    (0x1 << 2)
-#define DMC_MEMORY_CFG2_CKE_INIT    (0x1 << 3)
-#define DMC_MEMORY_CFG2_BANK_BITS_2    (0x0 << 4)
-#define DMC_MEMORY_CFG2_BANK_BITS_3    (0x3 << 4)
-#define DMC_MEMORY_CFG2_MEM_WIDTH_16    (0x0 << 6)
-#define DMC_MEMORY_CFG2_MEM_WIDTH_32    (0x1 << 6)
-#define DMC_MEMORY_CFG2_MEM_WIDTH_64    (0x2 << 6)
-#define DMC_MEMORY_CFG2_MEM_WIDTH_RESERVED  (0x3 << 6)
-
-//
-// DMC Configuration Register Map
-//
-#define DMC_STATUS_REG              0x00
-#define DMC_COMMAND_REG             0x04
-#define DMC_DIRECT_CMD_REG          0x08
-#define DMC_MEMORY_CONFIG_REG       0x0C
-#define DMC_REFRESH_PRD_REG         0x10
-#define DMC_CAS_LATENCY_REG         0x14
-#define DMC_WRITE_LATENCY_REG       0x18
-#define DMC_T_MRD_REG               0x1C
-#define DMC_T_RAS_REG               0x20
-#define DMC_T_RC_REG                0x24
-#define DMC_T_RCD_REG               0x28
-#define DMC_T_RFC_REG               0x2C
-#define DMC_T_RP_REG                0x30
-#define DMC_T_RRD_REG               0x34
-#define DMC_T_WR_REG                0x38
-#define DMC_T_WTR_REG               0x3C
-#define DMC_T_XP_REG                0x40
-#define DMC_T_XSR_REG               0x44
-#define DMC_T_ESR_REG               0x48
-#define DMC_MEMORY_CFG2_REG         0x4C
-#define DMC_MEMORY_CFG3_REG         0x50
-#define DMC_T_FAW_REG               0x54
-#define DMC_T_RDATA_EN              0x5C        /* DFI read data enable register */
-#define DMC_T_WRLAT_DIFF            0x60        /* DFI write data enable register */
-
-// Returns the state of the memory controller:
-#define DMC_STATUS_CONFIG       0x0
-#define DMC_STATUS_READY        0x1
-#define DMC_STATUS_PAUSED       0x2
-#define DMC_STATUS_LOWPOWER     0x3
-
-// Changes the state of the memory controller:
-#define DMC_COMMAND_GO              0x0
-#define DMC_COMMAND_SLEEP           0x1
-#define DMC_COMMAND_WAKEUP          0x2
-#define DMC_COMMAND_PAUSE           0x3
-#define DMC_COMMAND_CONFIGURE       0x4
-#define DMC_COMMAND_ACTIVEPAUSE     0x7
-
-// Determines the command required
-#define DMC_DIRECT_CMD_MEMCMD_PRECHARGEALL      0x0
-#define DMC_DIRECT_CMD_MEMCMD_AUTOREFRESH       (0x1 << 18)
-#define DMC_DIRECT_CMD_MEMCMD_MODEREG           (0x2 << 18)
-#define DMC_DIRECT_CMD_MEMCMD_EXTMODEREG        (0x2 << 18)
-#define DMC_DIRECT_CMD_MEMCMD_NOP               (0x3 << 18)
-#define DMC_DIRECT_CMD_MEMCMD_DPD               (0x1 << 22)
-#define DMC_DIRECT_CMD_BANKADDR(n)              ((n & 0x3) << 16)
-#define DMC_DIRECT_CMD_CHIP_ADDR(n)             ((n & 0x3) << 20)
-
-
-//
-// AXI ID configuration register map
-//
-#define DMC_ID_0_CFG_REG            0x100
-#define DMC_ID_1_CFG_REG            0x104
-#define DMC_ID_2_CFG_REG            0x108
-#define DMC_ID_3_CFG_REG            0x10C
-#define DMC_ID_4_CFG_REG            0x110
-#define DMC_ID_5_CFG_REG            0x114
-#define DMC_ID_6_CFG_REG            0x118
-#define DMC_ID_7_CFG_REG            0x11C
-#define DMC_ID_8_CFG_REG            0x120
-#define DMC_ID_9_CFG_REG            0x124
-#define DMC_ID_10_CFG_REG           0x128
-#define DMC_ID_11_CFG_REG           0x12C
-#define DMC_ID_12_CFG_REG           0x130
-#define DMC_ID_13_CFG_REG           0x134
-#define DMC_ID_14_CFG_REG           0x138
-#define DMC_ID_15_CFG_REG           0x13C
-
-// Set the QoS
-#define DMC_ID_CFG_QOS_DISABLE      0
-#define DMC_ID_CFG_QOS_ENABLE       1
-#define DMC_ID_CFG_QOS_MIN          2
-
-
-//
-// Chip configuration register map
-//
-#define DMC_CHIP_0_CFG_REG          0x200
-#define DMC_CHIP_1_CFG_REG          0x204
-#define DMC_CHIP_2_CFG_REG          0x208
-#define DMC_CHIP_3_CFG_REG          0x20C
-
-//
-// User Defined Pins
-//
-#define DMC_USER_STATUS_REG         0x300
-#define DMC_USER_0_CFG_REG          0x304
-#define DMC_USER_1_CFG_REG          0x308
-#define DMC_FEATURE_CRTL_REG        0x30C
-#define DMC_USER_2_CFG_REG          0x310
-
-
-//
-// PHY Register Settings
-//
-#define PHY_PTM_DFI_CLK_RANGE       0xE00  // DDR2 PHY PTM register offset
-#define PHY_PTM_IOTERM              0xE04
-#define PHY_PTM_PLL_EN              0xe0c
-#define PHY_PTM_PLL_RANGE           0xe18
-#define PHY_PTM_FEEBACK_DIV         0xe1c
-#define PHY_PTM_RCLK_DIV            0xe20
-#define PHY_PTM_LOCK_STATUS         0xe28
-#define PHY_PTM_INIT_DONE           0xe34
-#define PHY_PTM_ADDCOM_IOSTR_OFF    0xec8
-#define PHY_PTM_SQU_TRAINING        0xee8
-#define PHY_PTM_SQU_STAT            0xeec
-
-// ==============================================================================
-// PIPD 40G DDR2/DDR3 PHY Register definitions
-//
-// Offsets from APB Base Address
-// ==============================================================================
-#define PHY_BYTE0_OFFSET            0x000
-#define PHY_BYTE1_OFFSET            0x200
-#define PHY_BYTE2_OFFSET            0x400
-#define PHY_BYTE3_OFFSET            0x600
-
-#define PHY_BYTE0_COARSE_SQADJ_INIT 0x064  ;// Coarse squelch adjust
-#define PHY_BYTE1_COARSE_SQADJ_INIT 0x264  ;// Coarse squelch adjust
-#define PHY_BYTE2_COARSE_SQADJ_INIT 0x464  ;// Coarse squelch adjust
-#define PHY_BYTE3_COARSE_SQADJ_INIT 0x664  ;// Coarse squelch adjust
-
-#define PHY_BYTE0_IOSTR_OFFSET      0x004
-#define PHY_BYTE1_IOSTR_OFFSET      0x204
-#define PHY_BYTE2_IOSTR_OFFSET      0x404
-#define PHY_BYTE3_IOSTR_OFFSET      0x604
-
-
-;//--------------------------------------------------------------------------
-
-// DFI Clock ranges:
-
-#define PHY_PTM_DFI_CLK_RANGE_200MHz            0x0
-#define PHY_PTM_DFI_CLK_RANGE_201_267MHz        0x1
-#define PHY_PTM_DFI_CLK_RANGE_268_333MHz        0x2
-#define PHY_PTM_DFI_CLK_RANGE_334_400MHz        0x3
-#define PHY_PTM_DFI_CLK_RANGE_401_533MHz        0x4
-#define PHY_PTM_DFI_CLK_RANGE_534_667MHz        0x5
-#define PHY_PTM_DFI_CLK_RANGE_668_800MHz        0x6
-
-
-
-#define  PHY_PTM_DFI_CLK_RANGE_VAL              PHY_PTM_DFI_CLK_RANGE_334_400MHz
-
-//--------------------------------------------------------------------------
-
-
-// PLL Range
-
-#define PHY_PTM_PLL_RANGE_200_400MHz            0x0     // b0 = frequency >= 200 MHz and < 400 MHz
-#define PHY_PTM_PLL_RANGE_400_800MHz            0x1     // b1 = frequency >= 400 MHz.
-#define PHY_PTM_FEEBACK_DIV_200_400MHz          0x0     // b0 = frequency >= 200 MHz and < 400 MHz
-#define PHY_PTM_FEEBACK_DIV_400_800MHz          0x1     // b1 = frequency >= 400 MHz.
-#define PHY_PTM_REFCLK_DIV_200_400MHz           0x0
-#define PHY_PTM_REFCLK_DIV_400_800MHz           0x1
-
-#define TC_UIOLHNC_MASK                         0x000003C0
-#define TC_UIOLHNC_SHIFT                        0x6
-#define TC_UIOLHPC_MASK                         0x0000003F
-#define TC_UIOLHPC_SHIFT                        0x2
-#define TC_UIOHOCT_MASK                         0x2
-#define TC_UIOHOCT_SHIFT                        0x1
-#define TC_UIOHSTOP_SHIFT                       0x0
-#define TC_UIOLHXC_VALUE                        0x4
-
-#define PHY_PTM_SQU_TRAINING_ENABLE             0x1
-#define PHY_PTM_SQU_TRAINING_DISABLE            0x0
-
-
-//--------------------------------------
-// JEDEC DDR2 Device Register definitions and settings
-//--------------------------------------
-#define DDR_MODESET_SHFT                        14
-#define DDR_MODESET_MR                          0x0  ;// Mode register
-#define DDR_MODESET_EMR                         0x1  ;// Extended Mode register
-#define DDR_MODESET_EMR2                        0x2
-#define DDR_MODESET_EMR3                        0x3
-
-//
-// Extended Mode Register settings
-//
-#define DDR_EMR_OCD_MASK                        0x0000380
-#define DDR_EMR_OCD_SHIFT                       0x7
-#define DDR_EMR_RTT_MASK                        0x00000044                  // DDR2 Device RTT (ODT) settings
-#define DDR_EMR_RTT_SHIFT                       0x2
-#define DDR_EMR_ODS_MASK                        0x00000002                  // DDR2 Output Drive Strength
-#define DDR_EMR_ODS_SHIFT                       0x0001
-
-// Termination Values:
-#define DDR_EMR_RTT_50R                         0x00000044                  // DDR2 50 Ohm termination
-#define DDR_EMR_RTT_75R                         0x00000004                  // DDR2 75 Ohm termination
-#define DDR_EMR_RTT_150                         0x00000040                  // DDR2 150 Ohm termination
-
-// Output Drive Strength Values:
-#define DDR_EMR_ODS_FULL                        0x0                         // DDR2 Full Drive Strength
-#define DDR_EMR_ODS_HALF                        0x1                         // DDR2 Half Drive Strength
-
-// OCD values
-#define DDR_EMR_OCD_DEFAULT                     0x7
-#define DDR_EMR_OCD_NS                          0x0
-
-#define DDR_EMR_ODS_VAL                         DDR_EMR_ODS_FULL
-
-#define DDR_SDRAM_START_ADDR                    0x10000000
-
-
-// ----------------------------------------
-// PHY IOTERM values
-// ----------------------------------------
-#define PHY_PTM_IOTERM_OFF                      0x0
-#define PHY_PTM_IOTERM_150R                     0x1
-#define PHY_PTM_IOTERM_75R                      0x2
-#define PHY_PTM_IOTERM_50R                      0x3
-
-#define PHY_BYTE_IOSTR_60OHM                    0x0
-#define PHY_BYTE_IOSTR_40OHM                    0x1
-#define PHY_BYTE_IOSTR_30OHM                    0x2
-#define PHY_BYTE_IOSTR_30AOHM                   0x3
-
-#define DDR2_MR_BURST_LENGTH_4     (2)
-#define DDR2_MR_BURST_LENGTH_8     (3)
-#define DDR2_MR_DLL_RESET          (1 << 8)
-#define DDR2_MR_CAS_LATENCY_4      (4 << 4)
-#define DDR2_MR_CAS_LATENCY_5      (5 << 4)
-#define DDR2_MR_CAS_LATENCY_6      (6 << 4)
-#define DDR2_MR_WR_CYCLES_2        (1 << 9)
-#define DDR2_MR_WR_CYCLES_3        (2 << 9)
-#define DDR2_MR_WR_CYCLES_4        (3 << 9)
-#define DDR2_MR_WR_CYCLES_5        (4 << 9)
-#define DDR2_MR_WR_CYCLES_6        (5 << 9)
-
-
-VOID
-PL341DmcInit (
-  IN  UINTN             DmcBase,
-  IN  PL341_DMC_CONFIG* DmcConfig
-  );
-
-VOID PL341DmcPhyInit (
-  IN UINTN   DmcPhyBase
-  );
-
-VOID PL341DmcTrainPHY (
-  IN UINTN   DmcPhyBase
-  );
-
-#endif /* _PL341DMC_H_ */
-- 
2.11.0

_______________________________________________
edk2-devel mailing list
edk2-devel@lists.01.org
https://lists.01.org/mailman/listinfo/edk2-devel