UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1].

Add support by removing the no-1-8-v tag and including the voltage
regulator device tree nodes for power cycling.

[1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---

test logs:
https://pastebin.ubuntu.com/p/vpYbY9QWh8/

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi      |  1 -
 .../arm64/boot/dts/ti/k3-am654-base-board.dts | 33 +++++++++++++++++++
 2 files changed, 33 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index cb340d1b401f..632f32fce4a1 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -301,7 +301,6 @@
 		ti,otap-del-sel = <0x2>;
 		ti,trm-icp = <0x8>;
 		dma-coherent;
-		no-1-8-v;
 	};
 
 	scm_conf: scm-conf@100000 {
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 9e87fb313a54..6f7292b6fe0a 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -91,6 +91,38 @@
 		#clock-cells = <0>;
 		clock-frequency = <24000000>;
 	};
+
+	evm_12v0: fixedregulator-evm12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc3v3_io: fixedregulator-vcc3v3io {
+		/* Output of TPS54334 */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_io";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&evm_12v0>;
+	};
+
+	vdd_mmc1_sd: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vcc3v3_io>;
+		gpio = <&pca9554 4 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &wkup_pmx0 {
@@ -350,6 +382,7 @@
  * disable sdhci1
  */
 &sdhci1 {
+	vmmc-supply = <&vdd_mmc1_sd>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	ti,driver-strength-ohm = <50>;
-- 
2.17.1