The following series of patches add support for implementing the
transceiver as a phy of m_can_platform driver.

TCAN1042 has a standby signal that needs to be pulled high for
sending/receiving messages[1]. TCAN1043 has a enable signal along with
standby signal that needs to be pulled up for sending/receiving
messages[2], and other combinations of the two lines can be used to put the
transceiver in different states to reduce power consumption. On boards
like the AM654-idk and J721e-evm these signals are controlled using gpios.

These gpios are set in phy driver, and the transceiver can be put in
different states using phy API. The phy driver is added in the series [3].

[1] - https://www.ti.com/lit/ds/symlink/tcan1042h.pdf
[2] - https://www.ti.com/lit/ds/symlink/tcan1043-q1.pdf
[3] - https://lore.kernel.org/patchwork/project/lkml/list/?series=495365

Faiz Abbas (2):
  dt-bindings: net: can: Document transceiver implementation as phy
  can: m_can: Add support for transceiver as phy

 .../devicetree/bindings/net/can/bosch,m_can.yaml    |  3 +++
 drivers/net/can/m_can/m_can.c                       | 10 ++++++++++
 drivers/net/can/m_can/m_can.h                       |  2 ++
 drivers/net/can/m_can/m_can_platform.c              | 13 +++++++++++++
 4 files changed, 28 insertions(+)

-- 
2.17.1

Hi all,

On 15/04/21 8:36 pm, Aswath Govindraju wrote:
> The following series of patches add support for implementing the
> transceiver as a phy of m_can_platform driver.
> 
> TCAN1042 has a standby signal that needs to be pulled high for
> sending/receiving messages[1]. TCAN1043 has a enable signal along with
> standby signal that needs to be pulled up for sending/receiving
> messages[2], and other combinations of the two lines can be used to put the
> transceiver in different states to reduce power consumption. On boards
> like the AM654-idk and J721e-evm these signals are controlled using gpios.
> 
> These gpios are set in phy driver, and the transceiver can be put in
> different states using phy API. The phy driver is added in the series [3].
> 
> [1] - https://www.ti.com/lit/ds/symlink/tcan1042h.pdf
> [2] - https://www.ti.com/lit/ds/symlink/tcan1043-q1.pdf
> [3] - https://lore.kernel.org/patchwork/project/lkml/list/?series=495365
> 

Please ignore this series. I will post a respin using
devm_phy_get_optional instead of devm_of_phy_get_optional_by_index()
based on the comments below[1]. Sorry for the noise.

[1] - https://lore.kernel.org/patchwork/patch/1413931/

Thanks,
Aswath

> Faiz Abbas (2):
>   dt-bindings: net: can: Document transceiver implementation as phy
>   can: m_can: Add support for transceiver as phy
> 
>  .../devicetree/bindings/net/can/bosch,m_can.yaml    |  3 +++
>  drivers/net/can/m_can/m_can.c                       | 10 ++++++++++
>  drivers/net/can/m_can/m_can.h                       |  2 ++
>  drivers/net/can/m_can/m_can_platform.c              | 13 +++++++++++++
>  4 files changed, 28 insertions(+)
> 

Hi all,

On 15/04/21 8:36 pm, Aswath Govindraju wrote:
> The following series of patches add support for implementing the
> transceiver as a phy of m_can_platform driver.
> 
> TCAN1042 has a standby signal that needs to be pulled high for
> sending/receiving messages[1]. TCAN1043 has a enable signal along with
> standby signal that needs to be pulled up for sending/receiving
> messages[2], and other combinations of the two lines can be used to put the
> transceiver in different states to reduce power consumption. On boards
> like the AM654-idk and J721e-evm these signals are controlled using gpios.
> 
> These gpios are set in phy driver, and the transceiver can be put in
> different states using phy API. The phy driver is added in the series [3].
> 
> [1] - https://www.ti.com/lit/ds/symlink/tcan1042h.pdf
> [2] - https://www.ti.com/lit/ds/symlink/tcan1043-q1.pdf
> [3] - https://lore.kernel.org/patchwork/project/lkml/list/?series=495365
> 

Posted v2 for this series.

Thanks,
Aswath

> Faiz Abbas (2):
>   dt-bindings: net: can: Document transceiver implementation as phy
>   can: m_can: Add support for transceiver as phy
> 
>  .../devicetree/bindings/net/can/bosch,m_can.yaml    |  3 +++
>  drivers/net/can/m_can/m_can.c                       | 10 ++++++++++
>  drivers/net/can/m_can/m_can.h                       |  2 ++
>  drivers/net/can/m_can/m_can_platform.c              | 13 +++++++++++++
>  4 files changed, 28 insertions(+)
>